GrantR
Senior Member
- Joined
- Jul 16, 2007
- Messages
- 1,329
- Location
- Plains, GA
- Aircraft
- Kolb MarkIII and a "Jake" Gyroplane
- Total Flight Time
- About 85 fixed wing 3 gyro
Rotax 503
Single points ignition, Single Bing 54 carburetor. Unknown Hours runs excellent. Engine still has cross hatches on the cylinder walls! Engine comes with Belt reduction drive, Exhaust Y pipe and 60 inch Warp Drive prop. The belt reduction drive is about 9 inches tall and has a 2.2 to 1 ratio. I think it is a Quad City Challenger drive. A 60 inch warp drive prop is included that matches the redrive hub. One prop blade is damaged from a bolt strike. Warp Drive can fix the blade for around $75. The redrive started sheering a bolt on the side plate that attaches the side of the engine to the side of the redrive. I was told that this has never happened before. It started happening after I put 18 hours on the engine. I think it is just out of alignment. I think it can be corrected by tightening the side mount plate before tightening the bottom engine mount bolts.
Asking $1,200.00
Westach Dual CHT gauge. I don’t know if it works or not. The needles appear to be ok by comparing it to my other gauges. If it doesn’t work send it back to me for a refund.
Sells for $85 new. Will sell for $50.00.
11.25” Diameter X ¼” thick prerotater drive plate from rotor flight dynamics. Has a 6 bolt pattern and a 4 bolt pattern for the belt redrive and prop.
Paid $100 asking $75.00
Wunderlinch Flex cable
35.25 inch from end to end . New with only 18 hrs use. It spins clockwise looking down from above the rotorhead. Sells new for around $250 Asking $130.00
Wunderlinch lower drive unit. Wheel, housing and bearings are in good shape. Keyway has a bit of slop in it.
$40.00 SOLD!
Inflight adjustable trim made by Scott Essex. Paid $75, will take $60.00
Bolt on Gyro landing gear go kart shock ready.
Comes with 5/8” axles with castle nuts , custom disc brakes and a clamp mount for the axle tubes to attach to the keel. You will need to buy some wheels, U brackets; bolts and material to build a clamp mount for the drag struts. Azusa 6 inch nylon wheels fit the brake disc. This gear will give you a 5 foot stance.
Axle tubes are 26.75 inches long X 1.25X.125 wall 6061 t6 tubing.
Drag struts are 30.25” long X 1” X.125
Shock tubes are 1.25X.125 and step up to 1.375X.058 to fit around the shocks.
The cost of just the aluminum tubing alone is about $100. Asking $125.00
Will Sell everything together for $1,525.00 Shipping not included in any figures
Pictures and more details are here: https://picasaweb.google.com/109784086179485915351/GyroStuffForSale#
Single points ignition, Single Bing 54 carburetor. Unknown Hours runs excellent. Engine still has cross hatches on the cylinder walls! Engine comes with Belt reduction drive, Exhaust Y pipe and 60 inch Warp Drive prop. The belt reduction drive is about 9 inches tall and has a 2.2 to 1 ratio. I think it is a Quad City Challenger drive. A 60 inch warp drive prop is included that matches the redrive hub. One prop blade is damaged from a bolt strike. Warp Drive can fix the blade for around $75. The redrive started sheering a bolt on the side plate that attaches the side of the engine to the side of the redrive. I was told that this has never happened before. It started happening after I put 18 hours on the engine. I think it is just out of alignment. I think it can be corrected by tightening the side mount plate before tightening the bottom engine mount bolts.
Asking $1,200.00
Westach Dual CHT gauge. I don’t know if it works or not. The needles appear to be ok by comparing it to my other gauges. If it doesn’t work send it back to me for a refund.
Sells for $85 new. Will sell for $50.00.
11.25” Diameter X ¼” thick prerotater drive plate from rotor flight dynamics. Has a 6 bolt pattern and a 4 bolt pattern for the belt redrive and prop.
Paid $100 asking $75.00
Wunderlinch Flex cable
35.25 inch from end to end . New with only 18 hrs use. It spins clockwise looking down from above the rotorhead. Sells new for around $250 Asking $130.00
Wunderlinch lower drive unit. Wheel, housing and bearings are in good shape. Keyway has a bit of slop in it.
$40.00 SOLD!
Inflight adjustable trim made by Scott Essex. Paid $75, will take $60.00
Bolt on Gyro landing gear go kart shock ready.
Comes with 5/8” axles with castle nuts , custom disc brakes and a clamp mount for the axle tubes to attach to the keel. You will need to buy some wheels, U brackets; bolts and material to build a clamp mount for the drag struts. Azusa 6 inch nylon wheels fit the brake disc. This gear will give you a 5 foot stance.
Axle tubes are 26.75 inches long X 1.25X.125 wall 6061 t6 tubing.
Drag struts are 30.25” long X 1” X.125
Shock tubes are 1.25X.125 and step up to 1.375X.058 to fit around the shocks.
The cost of just the aluminum tubing alone is about $100. Asking $125.00
Will Sell everything together for $1,525.00 Shipping not included in any figures
Pictures and more details are here: https://picasaweb.google.com/109784086179485915351/GyroStuffForSale#
Last edited:
