Rotary Wing Forum  

Go Back   Rotary Wing Forum > Swap Meet > Wanted

Reply
 
Thread Tools Rate Thread Display Modes
  #1  
Old 11-23-2016, 07:54 PM
GK2's Avatar
GK2 GK2 is offline
Senior Member
 
Join Date: Feb 2012
Location: Rome, Ga
Posts: 413
Default Prop and some Mufflers

Does anyone know where I can get a prop 52, 26 and expansion chambers for a MAC motor 72 hp?
Reply With Quote
  #2  
Old 11-24-2016, 04:09 PM
phantom phantom is offline
Platinum Member
 
Join Date: Apr 2009
Location: Eagle River
Posts: 1,328
Default

Give Tennessee propellers a call, they make a beautiful prop, that's the same prop that I have on my direct drive Subaru.
Norm.
Reply With Quote
  #3  
Old 11-24-2016, 04:47 PM
Barney Bahle's Avatar
Barney Bahle Barney Bahle is online now
Senior Member
 
Join Date: Jul 2011
Location: Crossville, TN 38571
Posts: 376
Default

+1 for www.tn-prop.com The 52X28 on my VW was delivered to my door in 3 weeks for just over 600 bucks. Got it just in time for Wrens.
Reply With Quote
  #4  
Old 11-24-2016, 04:50 PM
dabkb2's Avatar
dabkb2 dabkb2 is online now
Dave Bacon
 
Join Date: Sep 2005
Location: Vista, Ca
Posts: 2,018
Default

You could try Arrowprop. It is what I use on a dirt strip, for 10 years and it is holding up good. Get the urethane leading edge.

The Tennessee was more laminations, I do not know if that is a good thing or not.

The Arrowprop is about half price

http://arrowprop.com/air.htm
__________________
David Bacon
Reply With Quote
  #5  
Old 11-24-2016, 05:26 PM
SandL's Avatar
SandL SandL is offline
Platinum Member
 
Join Date: Aug 2011
Location: Royal Wootton Bassett... UK
Posts: 1,376
Default

herculese propellers in the Uk will make any prop you want from vintage SE5a through to bensen, give them the spec and they will discuss, put through their computer and make a 2.3 .4 blader, push, pull or anything wood only i think. highly professional and very specific , so if you are stuck and know the HP, and reduction drive and clearence they will design and build the most efficient prop you will get.
Reply With Quote
  #6  
Old 12-21-2016, 03:44 PM
caciquefl's Avatar
caciquefl caciquefl is offline
Forum Supporter
 
Join Date: Sep 2016
Location: Pacific Islands
Posts: 10
Send a message via AIM to caciquefl Send a message via Yahoo to caciquefl Send a message via Skype™ to caciquefl
Default

I have two extra 3 Blad props at home with Hubs, Hit me up will post some pictures
Reply With Quote
  #7  
Old 12-21-2016, 07:47 PM
dabkb2's Avatar
dabkb2 dabkb2 is online now
Dave Bacon
 
Join Date: Sep 2005
Location: Vista, Ca
Posts: 2,018
Default

Quote:
Originally Posted by caciquefl View Post
I have two extra 3 Blad props at home with Hubs, Hit me up will post some pictures
Are they for a Mac? If so I am very interested.
__________________
David Bacon
Reply With Quote
  #8  
Old 01-11-2017, 03:24 AM
meglin meglin is offline
Member
 
Join Date: Feb 2016
Location: Kharkov
Posts: 56
Send a message via ICQ to meglin Send a message via Skype™ to meglin
Default

If I knew the engine speed and the estimated speed of flight, you could design a special propeller for your requirements. Of course, the fiberglass coating and protection of stainless steel edges.
The alternative - the propeller blades with carbon fiber diameter of 1400 or 1600 mm (55 and 63 ").
My site: http://propeller1.io.ua
__________________
Best regards, Vladimir Meglinsky
My site: http://propeller.simplesite.com/
Reply With Quote
  #9  
Old 01-11-2017, 05:42 AM
GK2's Avatar
GK2 GK2 is offline
Senior Member
 
Join Date: Feb 2012
Location: Rome, Ga
Posts: 413
Default

The prop I need is for a McCullouch drone motor. I would like to get the 52 26 prop for my gyro. Does anyone know of a nice used prop for sale?
Also did or does someone have any expansion chambers to go on the McCullouch motor. I would prefer to buy some ready to go instead of trying to build them.
Reply With Quote
  #10  
Old 01-13-2017, 06:26 AM
meglin meglin is offline
Member
 
Join Date: Feb 2016
Location: Kharkov
Posts: 56
Send a message via ICQ to meglin Send a message via Skype™ to meglin
Default

Unfortunately, I do not know the characteristics of this engine.
__________________
Best regards, Vladimir Meglinsky
My site: http://propeller.simplesite.com/
Reply With Quote
Reply

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -8. The time now is 06:52 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Ad Management plugin by RedTyger